RailFX cable railing kits come with stainless steel cable railing hardware fittings for both ends of your cable run, all washers and fasteners necessary, choice of 1/8″ or 3/16″ diameter 1×19 Type 316 stainless steel cable, and installation instructions.
Cable railing kits come in cable length increments of 5′ to 70′ lengths. You will cut the cables to their proper lengths on site. Each kit contains one cable and all associated hardware.
Accessories, such as mounting tabs, cable cutters, and other installation aids and equipment are ordered separately. For coastal applications in a salt water environment, it is strongly recommended E-Z Clean is purchased along with any kits. While Type 316 stainless steel, the most corrosion and rust-resistant stainless steel available, is used almost exclusively in our hardware, it is stain-less steel, not stain-proof. If you’re near the ocean, some maintenance will be required.
This Limited Lifetime Warranty applies to RailFX product purchased on or after April 13, 2023.
For RailFX product purchased from September 12, 2022 to April 12, 2023.
For RailFX product purchased prior to September 12, 2022.
Warranty Registration https://www.railfx.net/resources/warranty/#claim
Aluminum Railing Products
Each aluminum RailFX Product (as defined below) receives a high-quality powder coat paint finish applied in accordance with AAMA 2604 specifications. Nationwide TCC Acquisition, LLC (hereinafter “RailFX”) warrants that, subject to the terms and conditions below, its aluminum railing products (each, the “Aluminum Product”; more than one, the “Aluminum Products”) (i) shall be free of structural defects in workmanship and materials, and (ii) will not crack, chip, blister, peel or abnormally discolor, in accordance with AAMA 2604 specifications. SEE CARE AND MAINTENANCE GUIDELINES FOR FULL CLEANING REQUIREMENTS.
Stainless Steel Cable and Fittings Products
Each RailFX cable, cable fitting, and cable assembly product is manufactured using 316 marine grade stainless steel. RailFX warrants that, subject to the terms and conditions below, the Stainless Products shall be free of machining, mechanical, and structural defects in workmanship and material. Note: Stainless steel requires periodic care and maintenance. Depending on exposure to corrosive environments, 316-grade stainless steel may corrode, discolor, and/or develop surface rust over time. THIS IS NOT CONSIDERED A DEFECT. Corrosion, discoloration, and development of surface rust can be largely mitigated with proper care and cleaning. SEE CARE AND MAINTENANCE GUIDELINES FOR FULL CLEANING REQUIREMENTS.
Products Warranty Term
RailFX will warrant the Products for the shorter of: (i) lifetime of the Purchaser (as defined below), or (ii) as long as the Purchaser owns the structure on which the Product or Products are originally installed (altogether, the “Product Warranty”). The “Purchaser” is the living owner or owners (maximum of two) of the real estate and structure upon which the Product is installed at the time the install occurred. The Product Warranty is non-transferable to any other person or entity and will terminate upon the death of the last original owner or upon the conveyance or transfer of the real property or structure upon which the Product was originally installed.
Warranty Requirements
For the Product to remain eligible for coverage under the Warranties, the Purchaser (and/or the installer) must have complied with each of the following requirements:
The Purchaser must have completed the online product registration form (below) within thirty (30) days of the Product’s original purchase.
The Purchaser must have strictly adhered to RailFX’s cleaning and maintenance requirements. Please be aware that depending on the atmospheric conditions of the install area (such as for Products installed near the coastline), the Product may require more-frequent cleanings to remain in compliance with RailFX’s instructions.
Installation of the Product must have been completed in accordance with RailFX’s published installation instructions specific to each Product installed.
The Product must have been installed in accordance with local building codes and in a manner consistent with the Product’s normal use and condition.
The Product must not have been abused, neglected, or used in any manner other than that consistent with use as a pedestrian railing.
The Product must not have been exposed to harsh chemicals (such as pool treatments or ice removal products).
The Product must not have been improperly stored, transported, or handled.
The Product must have been installed in North America or on an island located in the Caribbean.
RailFX
Related Products
RailFX
RailFX Level Tensioner Fitting
RailFX Level Tensioner Fitting – Premium Cable Railing Connector for Wood Applications The RailFX Level Tensioner Fitting is an essential component of the RailFX Cable Railing System, designed...
RailFX
RailFX Stair Non-Tensioner Fitting
RailFX Stair Non-Tensioner Fitting – Premium Cable Railing Connector for Wood Stair Installations The RailFX Stair Non-Tensioner Fitting is a key component of the RailFX Cable Railing System,...
RailFX
RailFX Professional Cable Kits
Discover the RailFX Cable Kit, designed to provide a high-quality and easy-to-install cable railing solution for metal posts. Made in the USA from 1/8” high-quality 316 grade stainless steel, this...
RailFX
RailFX Stair-Angle Tensioner Fitting
RailFX Stair Tensioner Fitting – Premium Cable Railing Connector for Stair-Angle Installations The RailFX Stair Tensioner Fitting is an essential component of the RailFX Cable Railing System,...
RailFX
RailFx Express Mount - Post Template
RailFx Express Mount - Post Template The RailFx Express Mount - Post Template is an essential tool for ensuring precise cable fitting placement in your railing system. This template is designed to...